ASRock B75M-ITX Intel SCT Driver
Thank you for purchasing ASRock B75M-ITX motherboard, a reliable motherboard produced under Supports 3rd and 2nd Generation Intel® CoreTM i7 / i5 / i3 in. LGA 1 x RJ LAN Port with LED (ACT/LINK LED and SPEED. LED). Η ASROCK B75M-DGS είναι μια πολύ οικονομική μητρική με όλες τις τελευταίες τεχνολογίες που υπάρχουν αυτήν την στιγμή για το socket της Intel. Με την. ASRock B75M-ITX - Мнения, Дънни платки Оферти, B75M-ITX Mini-ITX Motherboard Supports Intel® Smart Connect, Intel® Rapid Start, Intel® Small Business Advantage 1 x RJ LAN Ports with LED (ACT/LINK LED and SPEED LED).
|Supported systems:||Windows All|
|Price:||Free* [*Free Registration Required]|
ASRock B75M-ITX Intel SCT Driver
This cap must be placed if returning the motherboard for after service. Insert the Pin CPU: Hold the CPU by the edge which is marked with a black line.
Дънна платка - ASROCK B75M-ITX
Locate Pin1 and the two orientation key notches. Carefully place the CPU into the socket by using a purely vertical motion. Verify that the CPU is within the socket and properly mated to the orient keys. Flip the load plate onto the IHS. Press down the load lever, and secure it with the load plate tab under the retention tab.
Before you install the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. Ensure that the CPU and the heatsink are securely fastened and in good contact with each other.
Which motherboard is better? ASRock B75M-ITX Mini ITX or Gigabyte GA-H77N-WIFI
For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink. Below is an example to illustrate the installation of the heatsink for Pin CPUs. Apply thermal interface material onto the center of the IHS on the socket ASRock B75M-ITX Intel SCT surface. Apply Thermal Interface Material Step 2.
Place the heatsink onto the socket. Align fasteners with the motherboard throughholes.
Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. Repeat with remaining fasteners. Fan cables on side closest to MB header Fastener slots pointing straight out Press Down 4 Places If you press ASRock B75M-ITX Intel SCT the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.
Connect fan header with the CPU fan connector on the motherboard. Secure redundant cable with tie-wrap to ensure the cable does not interfere with fan operation or contact other components. Otherwise, it will operate at single channel mode.
ASRock Z77TM-ITX User Manual: I/o Panel (b75m-itx)
If you install only one memory module or two non-identical memory modules, it is unable to activate Dual Channel Memory Technology. It is not recommended to install them on this motherboard. Unlock a DIMM slot by pressing the retaining clips outward.
Installing an expansion card Step 1. Before installing an expansion card, please make sure that ASRock B75M-ITX Intel SCT power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start ASRock B75M-ITX Intel SCT installation. Remove the system unit cover if your motherboard is already installed in a chassis. Remove the bracket facing the slot that you intend to use. Keep the screws for later use.
ASROCK B75M-ITX - описание.
Align the card connector with the slot and press firmly until the card is completely seated on the slot. Fasten the card to the chassis with screws. Replace the system cover 21 22 2.
To enable dual monitor feature, please follow the below steps: If you have installed onboard VGA driver from our support CD to your ASRock B75M-ITX Intel SCT already, you can freely enjoy the benefits of dual monitor function after your system boots. Please refer to the following steps to set up a surround display environment: Please refer to page 21 for proper expansion card installation procedures for details.
ASRock Z97E-ITX/AC Intel 1150 Mini ITX Motherboard with WiFi
Please make sure that the value ASRock B75M-ITX Intel SCT select is less than the total capability of the system memory. If you have installed the drivers already, there is no need to install them again. Set up a multi-monitor display. Right click the desktop, choose Properties, and select the Settings tab so that you can adjust the parameters of the multi-monitor according to the steps below.
Click the Identify button to display a large number on each monitor.