Asrock G31M-VS2 Instant Boot Driver
One buzz-kill - Instant Boot will also only work on Windows XP or Vista systems . Asrock G31M-VS2 motherboard BIOS - ASRG31MVS2 Free instant access to. Accelerator , DirectX , Max. shared memory MB, ErP/EuP Ready, Supports ASRock Instant Boot, Instant Flash, OC Tuner, Intelligent Energy Saver. Instant Boot支持列表与下载. 此功能仅适用于单个用户（未設定系统帐号和密码的用户）. Intel Socket Intel G31, G31M-VS2 · G31M-VS.
|Supported systems:||Windows XP/Vista/7/8/10, MacOS 10/X|
|Price:||Free* [*Free Registration Required]|
Asrock G31M-VS2 Instant Boot Driver
Hold components by the edges and do not touch the ICs.
- ASRock G31M-VS2 Bios Driver - TechSpot
- Welcome to ASRock Technical Support Forum! [Archive] - TweakTown Forums
- ASRock G31M-VS2 - motherboard - micro ATX - LGA775 Socket - G31
- G31M-VS2 Asrock Motherboard
- Marc Computers
- Asrock G31M-VS2 Drivers
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component. Before you install or remove any component, ensure that the power Asrock G31M-VS2 Instant Boot switched off or the power cord is detached from the power supply. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged. Disengaging the lever by depressing down and out on the hook to clear retention tab.
ASROCK G31M-VS2 BROCHURE Pdf Download.
Rotate the load lever to fully open position at approximately degrees. Rotate the load plate to fully open position at approximately degrees.
Hold the CPU by the edges where are marked with black lines. Locate Pin1 and the two orientation key notches. Carefully place the CPU into the socket by using a purely vertical motion.
Verify that the CPU is within the socket and properly mated to the orient keys. Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel Asrock G31M-VS2 Instant Boot cap from the socket while pressing on center of PnP cap to assist in removal. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.
This cap must be placed if returning the motherboard for after service. Rotate the load plate onto the IHS.
ASRock G31M-VS2 - motherboard - micro ATX - LGA Socket - G31 Overview - CNET
While pressing down lightly on load plate, engage the load lever. Secure load lever with load plate tab under retention tab of load lever. Before you installed the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. Ensure that the Asrock G31M-VS2 Instant Boot and the heatsink are securely fastened and in good contact with each other. For proper Asrock G31M-VS2 Instant Boot, please kindly refer to the instruction manuals of your CPU fan and heatsink.
Apply thermal interface material onto center of IHS on the socket surface. Place the heatsink onto the socket.
Align fasteners with the motherboard throughholes. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard. Connect fan header with the CPU fan connector on the motherboard.
ASRock G41M-VS2 motherboard for PC Gaming by ASRock
Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components. Otherwise, it will operate at single channel mode.
If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology. Unlock a DIMM slot by pressing the retaining clips outward.
The DIMM only fits in one correct orientation.